Photo: Chloe Count Go, go! DIY for this project you will need: 
Photo: Chloe Count
- 4 Chinese lanterns
- White cable (length to be determined by the height of the ceiling)
- Taken 1
- 1 switch
- 4 sockets
- Wire
- Insulating tape
- Screwdriver
- Exacto
- Wire cutter
- The stripper's son
- Small clamps
- Hanger
- Drill
- Anchor
- 4 light bulbs to energy saving or LED (these are lamps that do not heat so as not to burn paper lanterns).
Chart: To help you better understand what to do, here is a diagram of the lamp. 
Photo: Chloe Graf Step 1: We begin the implementation of the lamp from the bottom up. So we start to assemble the lamp lowest (closest is applied to the soil), and ending with the highest (one that will be closest to the ceiling). 
Photo: Chloe Count Open the black and the white inside of the casing of your wire retrieve it. Place them in a position to wind the copper threads on itself and form a hook to place in the socket. Put the lid of the socket on the electric cable. Attach the son of the socket gently tightening the screws in this crafting essentials. Sleeve in a white and a yellow screw. Make sure that you always put the same thread color to the same color screw. For example, the white wire goes to the silver screw and black wire to the screw golden step. 2: With the wire, form templates to guide the electrical line. So it will not touch the bulb, and it will stay straight up. 
Photo: Chloe Graf Step 3: Now place the electric wire (the one you just attach the lamp 1) on the wire and secure it with small clamps. 
Photo: Chloe Count As you can see from the picture, the thread, the top of the template reaches a little longer, because we are going to open the envelope we keep (to get the white and black wire). . All in order to connect a new lamp and make it out of the second thread will serve our 3rd lamp Step 4: Cut pieces with a knife protruding brackets. 
Photo: Chloe Graf Step 5: Now you'll be able to wire back up and thus positioning on our second lamp. Replace the cap on the base 2 electric line. Strip the rest two white coat, the two black and two white son son. 
Photo: Chloe Count Wrap the threads of two black son together and do the same with the 2 white son. Train hook with filaments son and insert it into the socket. Tighten the screws to secure the son of the socket. 
Photo :. Chloe Count Complete step 6 the cuff: To have a proper lamp also, I have the tape on white insulation around two white coat and my wire. Here is the result in pictures that you have to as often as desired to get the number of lanterns after repeating steps 3-6. For my part, I have 4 lamps balls, so I repeated 3 times. 
Photo: Chloe Graf Step 7: Install the screw on lamp bulbs and placing your lanterns on the mantle. Install your mounting hooks on the ceiling. Once the hook is set, hang it over your lamp to the desired length to be determined. 
Photo: Chloe Count It will just make the switch in a position to choose on the wire and plug everything Result: And now a new light decoration like paper! It will not cost much, but its effect is in more than one impression! 
Photo: Chloe Count Tips and Tricks:
- You will not be too much for this DIY 2. Tip: Get help.
- Please measure your ceiling height and diameter of your lanterns, to see how many you can place on your thread.
- You can either space the paper lanterns that stick. However pratico convenience, the more they will be inserted in the bulbs will be difficult to change.
Photo: Chloe Count
- Paper and heat do not mix. To prevent fire, energy saving lamps or LED lamps are used.
- Also note that you have placed multiple bulbs with each other. You do not need to have high power lamps. Bulbs 8 W or less perfectly adequate!
- So that the wire so that the center of each light, led I with a small clamp.
Good DIY!
